Products Lists

  1. Home
  2. cone crusher
  3. cause analysis of spindle fracture accident of cone crusher

Cause Analysis Of Spindle Fracture Accident Of Cone Crusher

Specializing in the production of jaw crusher, sand machine, ball mill, Raymond mill, cement equipment and other products. The main products are E-crusher, impact crusher, hammer crusher, impact crusher, Raymond mill, magnetic separator and other equipment,Whatever your requirements, you 'll find the perfect service-oriented solution to match your specific needs with our help.We are here for your questions anytime 24/7, welcome your consultation.

Chat Online
  • United States Mine Safety And Health

    United States Mine Safety And Health

    Aug 18, 2020 rock by hand from the cone crusher. By approximately 6:00 a.m., the miners had removed most of the rock near the cone crusher. Resendiz climbed down over the rock guard onto the cone crusher, kicking small material down and handing large material out to the other two miners. At 6:15 a.m., Aguilar noticed rock starting to trickle from the

    Live Chat
  • Department Of Labor Mine Safety And Health

    Department Of Labor Mine Safety And Health

    The accident occurred at the main plant in the cone crusher area. Cone Crusher The cone crusher is a Sandvik Model # CH550, Serial #0990S15216, with a fabricated feed box between the conveyor and the crusher. The cone crusher is the primary crusher at the main plant. (See Appendix B). West Amarillo installed the cone crusher and a new feed belt ...

    Live Chat
  • Teach You The Methods To Repair The Broken Shaft Of Cone

    Teach You The Methods To Repair The Broken Shaft Of Cone

    Fote Machinery will analyze the causes and solutions of this failure in the following paragraphs: After the analysis, we draw a conclusion that there are three general reasons for the fracture of main spindle during the process of cone crushing machine in the long run: its quality, external factors and the fatigue of …

    Live Chat
  • Opexshare  Serious Accident Alert  Fall From Cone Crusher

    Opexshare Serious Accident Alert Fall From Cone Crusher

    Oct 20, 2017 An accident occurred on July 25, 2017 when a miner was attempting to change the oil filter on the diesel motor for the cone crusher. The miner was using a filter wrench to remove the filter while standing on the battery box adjacent to the motor. The filter wrench broke and slipped causing the employee to fall about 5 feet to the ground causing injury.

    Live Chat
  • Gyratory Crusher  An Overview  Sciencedirect Topics

    Gyratory Crusher An Overview Sciencedirect Topics

    The cone crusher is a modified gyratory crusher. The essential difference is that the shorter spindle of the cone crusher is not suspended, as in the gyratory, but is supported in a curved, universal bearing below the gyratory head or cone (Figure 8.2). Power is transmitted from the source to the countershaft to a V-belt or direct drive.

    Live Chat
  • Reasons For The Fracture Of Main Shaft Of Symons Cone Crusher

    Reasons For The Fracture Of Main Shaft Of Symons Cone Crusher

    The main shaft is the core component of the Simmons cone crusher. The working principle is that the cone of the moving cone is press-fitted on the main shaft, and one end of the main shaft is inserted into the tapered hole of the eccentric sleeve. When the eccentric sleeve rotates, it drives the movable cone to make a swing motion.

    Live Chat
  • Cause Analysis And Problems Solving Of Jaw Crusher  Hxjq

    Cause Analysis And Problems Solving Of Jaw Crusher Hxjq

    Dec 10, 2019 Cause analysis: 1 The fastening bolts of the jaw plate are loose or dropped. 2 The discharge opening is too small, and the bottoms of the two jaw plates collide with each other. Solutions: 1 Tighten or matching bolts. 2 Adjust the discharge opening to ensure the correct clearance between the two jaws. The fracture of the bracket. Cause analysis:

    Live Chat
  • Crusher  An Overview  Sciencedirect Topics

    Crusher An Overview Sciencedirect Topics

    Cone crushers were originally designed and developed by Symons around 1920 and therefore are often described as Symons cone crushers. As the mechanism of crushing in these crushers are similar to gyratory crushers their designs are similar, but in this case the spindle is supported at the bottom of the gyrating cone instead of being suspended as in larger gyratory crushers.

    Live Chat
  • Department Of Labor Mine Safety And Health

    Department Of Labor Mine Safety And Health

    Aug 26, 2020 determine the cause of the accident. See Appendix B for a list of persons who participated in the accident investigation. DISCUSSION . Location of Accident The mine is 4.5 miles from Kalama, Washington. The staging area where the miners were preparing the jaw crusher for transport is approximately 1 mile off China Garden Road and 0.1

    Live Chat

HOW CAN WE HELP YOU?

If you have any questions or probloms about our products, please feel free to contact us!

contact btn